A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
We have noticed this great article about How to Install a Bathtub directly below on the net and decided it made perfect sense to discuss it with you over here.
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is readily accessible, the task can relocate immediately; if you have to open a wall surface to get rid of the old bathtub and position the brand-new tub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub and also embeded in the new one. Ensure you have actually certified yourself for the job and also fit attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to think about employing one prior to you begin. Chances are you might need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your bathroom if you have actually already acquired a new bathtub as well as don't need to transform the plan of your previous supply of water pipes.
Your devices as well as material list must consist of the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the restricted gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making sure that the washing machines are in place in between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap ends initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Making use of the two wooden boards under its feet, place the bathtub in the needed setting. The wood boards are handy in equally spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and also adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the furthest flexible tap connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the water as well as inspect all joints and new pipework for leakages and also tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub should wait till the bathtub has actually been made use of a minimum of once as this will resolve it right into its last setting.
Preparing for the Installation
To start with, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final setting.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break an inflexible seal, causing the water to permeate the wall between the bathroom and the tiling, causing complications with moisture and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always load the bath tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads on Tools You Need to Install a New Bathtub , I think sharing that piece of content was really helpful. Liked our entry? Please share it. Let someone else find it. I praise you for your time. Please come visit our site back soon.
Visit The Following Page
Report this page